Большое обновление пильных узлов

Смотреть

Тип техники

Бренд

Машина

Большое обновление пильных узлов

Смотреть

Открытый узел

Dozer Control Valve Linkage Two Lever (764255 - )

Серийный номер

Бренд

John Deere

Читать описание

100

баллов

Нашли неточность, знаете аналог или есть вопрос?

Воспользуйтесь этой формой и получите бонусы

№ на схеме	Серийный номер	Кол-во	Название	Описание
1	19H2477	1	CAP SCREW	5/16" X 1-1/4", (RESTRAIN LINK TO RESERVOIR)
2	T128678	2	Washer	-
3	AT49297	1	Link End	(RETAINING LINK TO RESERVOIR)
4	14H882	3	Nut	5/16", (RETAINS BALLJOINT TO LINK)
5	AT133014	1	Link	-
6	R11151	5	Lock Nut	(RESTRAINING LINK TO LEVER BASE) (RESTRAINING LINK CAPSCREW) (TWO USED-LINKS TO BALLJOINTS) (ANGLE LEVER TO LINK)
7	22H1009	2	Set Screw	1/4" X 5/16", (TIGHTEN AFTER SPECIAL NUT IS TIGHT) (INSTALL INTO SPECIAL BOLT HEAD AFTER LONG BALLJOINT INSTALLED)
8	T120990	1	Nut	(TIGHTEN NUT SECURELY AND INSTALL SET SCREW)
9	24H1265	5	Washer	13/16" X 1-1/4" X 0.060", (K), (BETWEEN PIVOT SHAFT ADJUSTABLE NUT AND PLASTIC COVER)
10	24H1390	2	Shim	(ADJACENT TO BUSHING)
11	T104220	4	Washer	(K), (INSTALL TWO IN ANGLE LEVER) (PRESS TWO INTO LEVER BASE)
12	19H2551	3	Cap Screw	5/16" X 3/4", (BALLJOINTS TO LEVER BASE)
13	24M7238	3	Washer	8.700 X 17 X 2 mm, (SMALL BALLJOINT CAPSCREWS TO LEVER BASE)
14	AT125890	1	Base	(ASSEMBLE TO LEVER BASE)
15	AT48548	3	Ball Joint	-
16	T123241	1	Bolt	-
17	AT124107	1	Ball Joint	(INSERT LONG LEG INTO SPECIAL BOLT AND THREAD TILL IT BOTTOMS)
18	14H865	1	Nut	1/2", (SECURE LONG BALLJOINT TO STRAP ON RESERVOIR FRONT PLATE)
19	11M7081	3	Cotter Pin	2.500 X 20 mm, (TWO SPOOL PINS) (ANGLE LEVER SPOOL PIN)
20	AT133015	2	Link	(LIFT AND TILT CONNECTING LINK)
21	P10456	3	Pin Fastener	(2 USED-LIFT AND TILT SPOOLS) (CONNECTING LINK TO VALVE SPOOL)
22	19H3307	1	Cap Screw	3/4" X 6", (PIVOT FOR ANGLE LEVER)
23	AT125892	1	Support	-
24	24M7240	2	Washer	13 X 25 X 3 mm, (PIVOT SHAFT SUPPORT NUTS)
25	19M7403	2	Cap Screw	M12 X 35, (PIVOT SHAFT SUPPORT TO RESERVOIR)
26	14M7275	2	Nut	M12, (PIVOT SHAFT SUPPORT TO RESERVOIR)
27	14H793	3	Nut	3/4", (TIGHTEN LEVER SHAFT ASSEMBLY UNTIL THERE IS MINIMUM SIDE PLAY ON ANGLE LEVER) (USE A LOCKNUT AGAINST ADJUSTMENT NUT) (SECURE PIVOT SHAFT TO SUPPORT TO KEEP FROM ROTATING)
28	AT104703	1	Ball Joint	-
29	AT113792	1	Tie Rod Assembly	(ANGLE FUNCTION TO THIRD VALVE SPOOL)
30	T104482	2	Bushing	(BETWEEN THICK PLASTIC SPACER AND OUTBOARD SUPPORT ARM)
31	T104483	1	Bushing	(BETWEEN LEVER AND OUTBOARD SUPPORT ARM)
32	T13333	1	Shim	(ONE ON EITHER SIDE OF LEVER - USE REMAINING TO SHIM LEVER IN POSITION)
33	AT113704	1	Lever	(ANGLE FUNCTION INBOARD SLOT)
34	T71570	1	Grip	(ANGLE LEVER)
35	T123244	1	Nut	(RETAINS LEVER ARM TO LEVER BASE)
36	14M7260	1	Nut	M16, (JAM NUT TO TIGHTEN LEVER TO BASE)
37	T124157	1	Shaft	(SECOND LEVER)
38	T68099	1	KNOB	(SECOND FUNCTION LEVER)

Dozer Control Valve Linkage Two Lever (764255 - )

Нет текстового описания