Большое обновление пильных узлов

Смотреть

Тип техники

Бренд

Машина

Большое обновление пильных узлов

Смотреть

Открытый узел

SPEED CHANGE GEARS AND SHAFTS (HI-LO-REVERSE TRANSMISSION) [01G06]

Серийный номер

Бренд

John Deere

Читать описание

100

баллов

Нашли неточность, знаете аналог или есть вопрос?

Воспользуйтесь этой формой и получите бонусы

№ на схеме	Серийный номер	Кол-во	Название	Описание
1	11M7087	1	Cotter Pin	4 X 40 MM
2	14H875	1	Nut	7/8", (SUB T32335, THIS APPLICATION)
2	T36149	1	LOCK NUT	1-1/8"
2	T32335	1	LOCK NUT	7/8"
3	T24749	1	SNAP RING	(SUB FOR T13711)
4	JD8929	1	Bearing Cone	-
5	JD8251	1	Bearing Cup	-
6	T13379	1	SNAP RING	-
7	T20802	1	SHIM	0.18 MM (.007")
7	T20803	1	SHIM	0.13 MM (.005")
7	T20804	1	SHIM	0.25 MM (.010")
8	T20800	1	SPACER	-
9	T31803	1	GEAR	3RD AND 4TH SPEED (31 AND 38 TEETH) (ALSO ORDER T31800) (SUB FOR T20799)
10	T31800	1	SHIFT COLLAR	(SUB FOR T23519)
11	T20794	2	GEAR	(31 TEETH)
12	T31799	3	WASHER	(SUB FOR T20793)
13	T31802	1	GEAR	7TH AND 8TH SPEED, WITH BUSHING (31 AND 26 TEETH) (SUB FOR T20798)
14	T20797	1	PLATE	-
15	T31801	1	GEAR	5TH AND 6TH SPEED (31 AND 32 TEETH) (SUB FOR T20796)
16	T31798	1	GEAR	1ST AND 2ND SPEED (31 AND 43 TEETH) (SUB FOR T20792)
17	JD8255	1	Bearing Cup	-
18	JD8941	1	Bearing Cone	-
19	-	1	Part 23	(.446 HOLE SIZE) (IF HUB IS MARKED T18062 AT59731 MUST BE ORDERED, T18062 IS NO LONGER AVAILABLE)
19	T41190	1	HUB	(SUB FOR T31827) (.522 HOLE SIZE)
20	T16573	1	Pin	-
21	JD8230	1	Bearing Cup	-
22	JD8194	1	Bearing Cone	-
23	T20787	1	SHAFT	-
24	R43244	1	Needle Roller	(SUB FOR T13712 AND T36816)
25	JD8171	1	Bearing Cone	-
26	JD8217	1	Bearing Cup	-
27	T31792	1	SHIM	0.05 MM (.002") (SUB FOR T17199)
27	T31793	1	SHIM	0.13 MM (.005") (SUB FOR T17200)
27	T31794	1	SHIM	0.25 MM (.010") (SUB FOR T17201)
28	T31800	1	SHIFT COLLAR	(USE WHEN T31803 THIRD AND FOURTH SPEED GEAR HAS BEEN INSTALLED AS A REPLACEMENT PART) (SUB FOR T23519)
29	T19411	1	WASHER	(NOT REQUIRED WITH T32335 NUT OR T36149 NUT)
30	17H91	1	RIVET	1/2" X 2"
30	16H1592	1	RIVET	7/16" X 1-3/4"
31	AT59731	1	PINION SHAFT	SHAFT, PINION (8 TEETH) WITH RING GEAR (MARKED T31826) (44 TEETH) (MATCHED SET) AND HUB (MARKED T41190) WITH RIVETS AND T64254 NUT, (SUB FOR AT18553) (MARKED T20791, T20775, T18062 AND AT30888)

SPEED CHANGE GEARS AND SHAFTS (HI-LO-REVERSE TRANSMISSION) [01G06]

Нет текстового описания